Mainstream Arm Embedded Processors ST STM32F479BGT6 MCU Microcontroller Integrated Circuit

STM32F479BGT6 MCU Integrated Circuits Microcontrollers Ics Mainstream Arm Embedded Processors St  

• ARM Microcontrollers - MCU High-performance advanced line, Arm Cortex-M4 core DSP & FPU, 1 Mbyte of Flash 1
• Arm®Cortex®-M4 32b MCU+FPU, 225DMIPS, up to 2MB Flash/384+4KB RAM, USB OTG HS/FS, Ethernet, FMC, dual Quad-SPI, Crypto, Graphical accelerator, Camera IF, LCD-TFT & MIPI DS
• Core: Arm® 32-bit Cortex®-M4 CPU with FPU, adaptive real-time accelerator (ART Accelerator™) allowing 0-wait state execution from Flash memory, frequency up to 180 MHz, MPU, 225 DMIPS/1.25 DMIPS/MHz (Dhrystone 2.1), and DSP instructions 
• Memories
  • – Up to 2 MB of Flash memory organized into two banks allowing read-while-write
  • – Up to 384+4 KB of SRAM including 64 KB of CCM (core coupled memory) data RAM
  • – Flexible external memory controller with up to 32-bit data bus: SRAM, PSRAM, SDRAM/LPSDR, SDRAM, Flash NOR/NAND memories
  • – Dual-flash mode Quad-SPI interface
• Graphics
  • – Chrom-ART Accelerator™ (DMA2D), graphical hardware accelerator enabling enhanced graphical user interface with minimum CPU load
  • – LCD parallel interface, 8080/6800 modes
  • – LCD TFT controller supporting up to XGA resolution
  • – MIPI® DSI host controller supporting up to 720p 30 Hz resolution
• Clock, reset and supply management
  • – 1.7 V to 3.6 V application supply and I/Os
  • – POR, PDR, PVD and BOR – 4-to-26 MHz crystal oscillator
  • – Internal 16 MHz factory-trimmed RC (1% accuracy)
  • – 32 kHz oscillator for RTC with calibration
  • – Internal 32 kHz RC with calibration
• Low power
  • – Sleep, Stop and Standby modes
  • – VBAT supply for RTC, 20×32 bit backup registers + optional 4 KB backup SRAM
• 3× 12-bit, 2.4 MSPS ADC: up to 24 channels and 7.2 MSPS in triple interleaved mode
• 2× 12-bit D/A converters
• General-purpose DMA: 16-stream DMA controller with FIFOs and burst support
• Up to 17 timers: up to twelve 16-bit and two 32-bit timers up to 180 MHz, each with up to four IC/OC/PWM or pulse counter and quadrature (incremental) encoder input. 2x watchdogs and SysTick timer
•  Debug mode
  • – SWD and JTAG interfaces
  • – Cortex®-M4 Trace Macrocell™
• Up to 161 I/O ports with interrupt capability
  • – Up to 157 fast I/Os up to 90 MHz
  • – Up to 159 5 V-tolerant I/Os
• Up to 21 communication interfaces
  • – Up to three I2C interfaces (SMBus/PMBus)
  • – Up to four USARTs and four UARTs (11.25 Mbit/s, ISO7816 interface, LIN, IrDA, modem control) – Up to six SPIs (45 Mbits/s), two with muxed full-duplex I2S for audio class accuracy via internal audio PLL or external clock – 1x SAI (serial audio interface)
  • – 2× CAN (2.0B Active)
  • – SDIO interface
• Advanced connectivity
  • – USB 2.0 full-speed device/host/OTG controller with on-chip PHY
  • – USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, on-chip full-speed PHY and ULPI
  • – Dedicated USB power rail enabling on-chip PHYs operation throughout the entire MCU power supply range
  • – 10/100 Ethernet MAC with dedicated DMA: supports IEEE 1588v2 hardware, MII/RMII
• 8- to 14-bit parallel camera interface up to 54 Mbytes/s
• Cryptographic accelerator
  • – HW accelerator for AES 128, 192, 256, Triple DES, HASH (MD5, SHA-1, SHA-2) and HMAC  True random number generator
• CRC calculation unit
• RTC: subsecond accuracy, hardware calendar
• 96-bit unique ID

• STM32F479BGT6 ARMCORTEX-M4180MHZ.PDF

•  ABS anti-lock braking system
•  GPS navigation system
•  engine intelligent electronic controller
•  LCD drive controller
• Smart appliances
• Wireless charging for consumer electronics